PRECISION Multiproduct Calibrator

  • 0 – 1000V DC / AC Voltage
  • 0 – 30A DC / AC Current
  • 0 – 1 GOhm Resistance
  • 1nF – 10mF Capacitance
  • 1Hz – 10MHz Frequency
  • Range of external accessories to increase workload





The 3000 series offers the widest workload coverage of any multi-product calibrator, with the ability to calibrate 18 types of instrument. It has the power to drive older analogue instruments alongside the accuracy to calibrate modern digital instruments.


The 3000 series features three models designed to suit every budget and accuracy requirement, and with a wide range of options that allow your calibrator to be tailored to meet your needs, the 3000 series is expandable for future needs.


Automate calibration with Procal – the world’s easiest to use multi-discipline calibration software for maximum calibration throughput.

3041A Specifications

3041A Specifications


Best 1 Year Total Accuracy

0 - ±1000V


Best 1 Year Total Accuracy

0 - ±30A


Best 1 Year Total Accuracy

20mV - 1000V, 10Hz - 500MHz


Best 1 Year Total Accuracy

20uA - 30A, 10Hz - 10kHz


Best 1 Year Total Accuracy

0 - 1 GOhms


Best 1 Year Total Accuracy

1nF - 10uF


Best 1 Year Total Accuracy

1Hz - 10MHz
20ppm (1ppm Option)


Best 1 Year Total Accuracy

J / K / T / R / S / B / U / N / E / L / U / C / 10uV°C



3000 Series

Transmille oscilloscope calibration options have amplitude ranges up to 300V to offer calibration of a wider range of oscilloscopes than our competitors.

Examples of oscilloscopes that require verification at these ranges are the Tektronix THS700A series and the Hanascope 801.

Transmille’s EA001/EA001A has been designed to minimise typical errors associated with calibration of thermocouple meters that are ignored by other designs.

By making the thermocouple option external, the low voltage output (in the order of 0mV to 100mV, with accuracies in the microvolt level required for accurate simulation) is away from any heat generating components in the calibrator therefore reducing any localised thermal EMF effects.

The inclusion of a Thermocouple plug removes the need to find compensation cables of the correct type, which is a considerable source of error. If the wrong type of compensation cable (for example, when simulating a K type thermocouple, a J type compensating cable) is used there will be a significant error introduced through use of the wrong cable.

Finally, a temperature measurement is conducted at the connection with the UUT, in the thermocouple plug itself. This is measuring the cold junction as close to the internal measurement of the UUT as possible, removing localised differences in temperature.

For further information on the design of our thermocouple option, please view our YouTube video HERE.

Transmille products have been designed to most accurately represent the requirements of modern commercial laboratories and the typical equipment that is found inside.

Almost all modern computers are fitted with a USB interface, so to enable direct connection without the requirement for additional adapters a USB connection is provided.

IEEE 488/GPIB interfaces are typically quite expensive, and are another lead/connection to remember when performing on-site calibration work.

GPIB interface options are available on our multiproduct calibrators, and are included as standard on the 8000 series multimeters.

The 30A output on Transmille multiproduct calibrators is included to ensure not only calibration of clamp meters up to 1500A, but also for calibration of low value high current shunts that would otherwise require a dedicated power supply which is an additional instrument that requires calibration.

The 30A function is limited by a thermal cut-out, that when the units internal temperature reaches a predetermined limit the output will be turned off.

The length of time that the 30A output is active for depends mainly upon the load that is connected, a higher resistance of load will mean that more power is dissipated within the load, reducing the self-heating of the high current section of the calibrator.

The worst-case scenario is that of a short across the output terminals, where all of the heat is being dissipated inside the heatsink of the calibrator. In the case of a coil that provides a considerable load (especially at AC, where the resistive and inductive effects of the coil take effect) the 30A can be present for much longer as the heat is being dissipated inside the coil.

We believe that safety is a prime consideration of a laboratory, second only to performance of our products.

Imagine a situation where a laboratory technician has finished calibration for the day, and has disconnected the instrument under test, but left the voltage source on at a setting of 1000V AC.

Later that evening, a cleaner comes into your laboratory or facility and touches the test leads left on the bench, potentially receiving a very nasty shock. Transmille have added this safety feature to avoid situations of this type from happening.

There are, however, cases where the timeout wishes to be extended, or even disabled. This can be performed through the Calibrator Setup program via your computer, or can be disabled prior to shipping on request.

3041A Resources
3000A Calibration Resources

3000A Calibration Resources

Transmille Product Guide
Transmille Warranty

Transmille Warranty

Videos & Demos

Videos & Demos

3000A Service Guide - Entering Calibration Mode

In this video, we show how to enter the calibration mode of the 3000A series multiproduct calibrator from the front panel.

3000A Service Guide - Adjusting DC Voltage

In this video we show how to adjust the DC voltage output of the 3000A series multiproduct calibrator. Using the guided calibration mode this is a simple procedure, which can be performed in just a few minutes.

3000A Service Guide - Adjusting AC Voltage

In this video we demonstrate how to adjust the AC voltage output of the 3000A series multiproduct calibrator.

3000A Service Guide - Output Protection Fuse Replacement

In this video we show how to diagnose and replace the front panel output protection fuses on the 3000A series calibrator.

How To - Calibrate a Multimeter with the 3000A Calibrator

In this video we demonstrate how to verify key features of a typical digital multimeter using a 3010A Multiproduct Calibrator

Options & Accessories

Calibrate low value high current shunts up to 100A and clamp meters up to 2000A using the EA3012A Transconductance Amplifier

  • 100 DC/70A AC up to 400Hz
  • Stackable for higher currents
  • Low-noise ultra linear MOSFET technology
  • Controlled directly via front panel of calibrator
  • Automation through ProCal software
  • Ideal for calibrating high current shunts, meters and clamp meters

Increase your laboratory capability with the ability to calibrate power supplies up to 3A/63V

  • Measures voltage up to 63V
  • Active current load to 3A
  • Calculates output resistance of a power supply for complete calibration

Increase your laboratories workload coverage to include high current power supplies with up to 60A/100V outputs.

  • Easy to use, low cost solution
  • Accurate, stable electronic load
  • Minimises equipment required for calibration


Option FRQ

For calibration of high accuracy frequency counters, a 1ppm high stability frequency output is available on 3000/4000 only.


Option GPIB

Additional GPIB / IEEE 488 interface for connecting into existing systems


Option IND

For full calibration of LCR meters, an inductance output is required. Option IND adds 8 fixed inductance values to enable complete calibration, available on 3000/4000 only.



Option PWRDDS expands on the functionality of PWRSINE by adding the ability to simulate harmonics, distortion, dropouts and flicker for calibration of power meters with power quality functions,available on 3000/4000 only.



Enables calibration of power and wattmeters, with a dynamically controlled phase relationship between voltage and current outputs available on 3000/4000 only.


Option SCP350

Providing calibration for oscilloscopes to 350Mhz bandwidth available on 3000/4000 only.


Option SCP600

Providing calibration for oscilloscopes to 600Mhz bandwidth available on 3000/4000 only.

For integration in to mobile test systems, or permanent installation in a laboratory, a 19" rack system is provided



In addition to passive resistance fitted as standard, option SIMRC adds variable resistance and simulated capacitance outputs available on 3000/4000 only.