4015

Advanced Multiproduct Calibrator

  • 0 – 1000V DC / AC Voltage
  • 0 – 30A DC / AC Current
  • Variable Resistance up to 1GOhm
  • Variable Capacitance to 100mF
  • 1Hz – 10MHz Frequency
  • AC current maximum frequency 30kHz
  • Range of external accessories to increase workload
  • USB and GPIB interface fitted as standard
  • Removable Handles

ASK AN EXPERT

Information

Description

SOFTWARE COMPATIBILITY

As with all Transmille products, compatibility with ProCal calibration software is guaranteed. Existing procedures will not need to be re-written due to Transmille’s unique implementation of flexible standards support where procedures are written around the UUT not the standard.

4010 Resources
Transmille Product Guide
Transmille Warranty

Transmille Warranty

Videos & Demos

Videos & Demos

4000 SERIES - DIRECT OHMS SELECTION

In this short video we demonstrate the latest updates to the 4000 series. The addition of new function keys enable direct access to the decade passive resistors enabling outputs to be directly accessed with a single touch of the screen.

4000 Series - Automated Verification

An example of the automated verification functionality using a Transmille 8081 precision multimeter.

4000 Series - Procedure Mode

Demonstration of the built-in procedure mode using a typical multimeter.

Options & Accessories

External

4000 Lead

A comprehensive set of test leads providing every connection required for typical measurements

External

4xxx Soft Case

A comprehensive set of test leads providing every connection required for typical measurements

A superior thermocouple simulation/measurement option, using a unique external adapter.

  • Offers fast and accurate calibration of thermocouple meters
  • Uses an innovative external measurement of cold junction temperature for ultimate accuracy
  • Utilising a thermocouple plug removes the requirement for expensive thermocouple compensation cable
 

Calibrate clamp meters at up to 1500A using the EA002 clamp meter. A unique design enables clamps of all sizes to be used, while minimising errors due to alignment

  • Calibrates clamp meters up to 1500A (30A input)
  • 2/10/50 Turn Coils
  • High accuracy AC/DC design, with minimal errors due to alignment
  • Wide range of clamp sizes covered, from 10mm jaw diameter to larger clamps
  • Alignment table included for accurate and repeatable readings

Instantly add the ability to calibrate tachometers to 60,000 RPM by adding the EA003 to your calibrator

  • High-intensity LED light source
  • Direct keyboard input in RPM
  • Control via ProCal for fully automated calibration
  • Output range from 60 to 60,000 RPM

Adds measurement capability to 1pA resolution, and measures high value resistors to 1TOhm using the calibrator as a precision DC voltage source

  • Accurate current measurement down to 1pA resolution
  • Ideal for high value resistance measurements up to 1 TOhm
  • High resistance measurement voltages up to 1000V
  • 5 current measurement rnages from 10nA to 100uA
  • Control directly from the calibrator front panel or use with ProCal software

As multimeters add more accurate low current ranges, traditional multi-product calibrators lack the precision and noise level for accurate calibration. With the EA013 pA source adapter, calibration of these instruments becomes simple

  • Ideal for calibration of electrometer instruments
  • Source accurate current down to picoamp levels
  • Low open circuit compliance voltage
  • Safe to use on sensitive input circuits
  • Controlled directly from the calibrator front panel or via supplied software
  • Compatible with ProCal for full measurement automation

Extend your laboratory's capabilities with the ability to calibrate torque screwdrivers and much more

Combining Transmille's most popular options, the EA015 provides a cost-effective method of increasing the workload coverage of Transmille calibrators

  • Insulation Testers
  • Continuity Testers
  • Optical Tachometers
  • Thermocouple Meters
  • Clamp Meters
  • Source functions of process control meters

Measure environmental factors both on site and in the laboratory

  • Humidity measurement from 10% to 90%
  • Temperature measurement from 0°C to 50°C

Automate calibration of 4 channel oscilloscopes with automised switching of channels with the EA017 adapter

  • 4 Output channels for automating oscilloscope calibration
  • Minimises lead changing when calibrating oscilloscopes
  • Choose between direct or buffered outputs for amplitude calibration

Calibrate low value high current shunts up to 100A and clamp meters up to 2000A using the EA3012A Transconductance Amplifier

  • 100 DC/70A AC up to 400Hz
  • Stackable for higher currents
  • Low-noise ultra linear MOSFET technology
  • Controlled directly via front panel of calibrator
  • Automation through ProCal software
  • Ideal for calibrating high current shunts, meters and clamp meters