UK
USA
India
Calibration Services
- 17025 Accredited AC Voltage calibration services from 2mV to 28 kV
- 10Hz to 1MHz capability depending upon level
References & Standards
PRECISION REFERENCES AND STANDARDS
- Shunt values for measurements between 1mA to 100A
- Low inductance & capacitance flat frequency response
- AC/DC differences from 1ppm
- From DC to 30kHz
- Simplifies precision calibration of calibrators and current sources
- Can be used with a precision multimeter or an AC measurement standard
Calibration Services
- 17025 Accredited Resistance calibration from 100 uOhm to 1 TOhm, with a wide capability with uncertainties lower than 1 ppm
External
The BreakD option allows the 3200 to calibrate both voltage output and current measurements of HiPot and Breakdown testers up to 12kV AC/DC
- 4 voltage ranges: 3kV & 12kV, AC and DC Voltage
- 9 Load Resistors/Current Ranges: 50kOhms (20mA) to 20MOhms (20uA) @ 1kV
Calibration Services
- Accredited measurements from 10pF to 10uF
- Measurement at 1kHz
A superior thermocouple simulation/measurement option, using a unique external adapter.
- Offers fast and accurate calibration of thermocouple meters
- Uses an innovative external measurement of cold junction temperature for ultimate accuracy
- Utilising a thermocouple plug removes the requirement for expensive thermocouple compensation cable
Calibration Services
- 17025 Accredited Inductance calibration from 10 uH to 1 H at 1 kHz, with the capability to measure and generate up to 100 H for traceable calibrations
External
Calibrate clamp meters at up to 1500A using the EA002 clamp meter. A unique design enables clamps of all sizes to be used, while minimising errors due to alignment
- Calibrates clamp meters up to 1500A (30A input)
- 2/10/50 Turn Coils
- High accuracy AC/DC design, with minimal errors due to alignment
- Wide range of clamp sizes covered, from 10mm jaw diameter to larger clamps
- Alignment table included for accurate and repeatable readings
Calibration Services
- 17025 Accredited Time & Frequency measurement and generation from 10 mHz to 1 GHz
Instantly add the ability to calibrate tachometers to 60,000 RPM by adding the EA003 to your calibrator
- High-intensity LED light source
- Direct keyboard input in RPM
- Control via ProCal for fully automated calibration
- Output range from 60 to 60,000 RPM
Calibration Services
- 17025 Accredited Simulation of PRT / RTD and Thermocouple Temperature
Adds measurement capability to 1pA resolution, and measures high value resistors to 1TOhm using the calibrator as a precision DC voltage source
- Accurate current measurement down to 1pA resolution
- Ideal for high value resistance measurements up to 1 TOhm
- High resistance measurement voltages up to 1000V
- 5 current measurement rnages from 10nA to 100uA
- Control directly from the calibrator front panel or use with ProCal software
External
As multimeters add more accurate low current ranges, traditional multi-product calibrators lack the precision and noise level for accurate calibration. With the EA013 pA source adapter, calibration of these instruments becomes simple
- Ideal for calibration of electrometer instruments
- Source accurate current down to picoamp levels
- Low open circuit compliance voltage
- Safe to use on sensitive input circuits
- Controlled directly from the calibrator front panel or via supplied software
- Compatible with ProCal for full measurement automation
External
Extend your laboratory's capabilities with the ability to calibrate torque screwdrivers and much more
Combining Transmille's most popular options, the EA015 provides a cost-effective method of increasing the workload coverage of Transmille calibrators
- Insulation Testers
- Continuity Testers
- Optical Tachometers
- Thermocouple Meters
- Clamp Meters
- Source functions of process control meters
Measure environmental factors both on site and in the laboratory
- Humidity measurement from 10% to 90%
- Temperature measurement from 0°C to 50°C
Automate calibration of 4 channel oscilloscopes with automised switching of channels with the EA017 adapter
- 4 Output channels for automating oscilloscope calibration
- Minimises lead changing when calibrating oscilloscopes
- Choose between direct or buffered outputs for amplitude calibration
Enables calibration of source functions of Process Control instruments including voltage, current and resistance.
- Extends workload of 1000 Series Calibrators
- Measure source functions from process control instruments
- Voltages up to 30V
- Currents up to 30A
- 2 and 4 wire resistance up to 10 kOhms
- 24V loop supply
Calibrate low value high current shunts up to 100A and clamp meters up to 2000A using the EA3012A Transconductance Amplifier
- 100 DC/70A AC up to 400Hz
- Stackable for higher currents
- Low-noise ultra linear MOSFET technology
- Controlled directly via front panel of calibrator
- Automation through ProCal software
- Ideal for calibrating high current shunts, meters and clamp meters